7″ Touch Screen All-In-One Kit Designed for Raspberry Pi CM4, 5MP Camera, Aluminum Case

Product Weight: 0.8000KG

CM4 socket	suitable for all variants of Compute Module 4
Networking	Gigabit Ethernet RJ45
Networking	M.2 M KEY, supports NVME SSD
USB	USB 2.0 × 4
Connector	isolated RS485, RS232, GPIO, and I2C
Display	7inch, 800 × 480 pixels, 5-points capacitive touch, toughened glass panel
Camera	5MP, F2.4, 3.89mm fixed focal length, supports video recording
Video	HDMI, supports 4K 30fps output
RTC	Real-time clock with battery socket and ability to wake Compute Module 4
Storage	MicroSD card socket for Compute Module 4 Lite (without eMMC) variants
Fan	5V/12V, allows speed adjustment and measurement
Speaker	8Ω 2W dual track speakers
Power input	7-36V
Dimensions	196.68 × 114.42mm

7inch capacitive touch screen, 5-points capacitive touch
along with toughened glass panel, more safe to use

providing interfaces including: CSI, HDMI, USB, M.2, ETH, RS232, RS485

CM4 socket
suitable for all variants of Compute Module 4
DC power supply
7 ~ 36V DC input
CM4 status indicator
PWR: Raspberry Pi power indicator
ACT: Raspberry Pi operating status indicator
HDMI connector
supports 4K 30fps output
RJ45 Gigabit Ethernet
10/100/1000M compatible
USB 2.0 ports
4x USB 2.0, for connecting sorts of USB devices
Micro SD card slot
for connecting a Micro SD card with pre-burnt image (Lite variant ONLY)
USB SLAVE port
USB programming port
BOOT selection
ON: CM4 will be booted from USB-C interface
OFF: CM4 will be booted from eMMC or Micro SD card
MIPI CSI connector
connected to the 5MP front camera
Isolated I2C
for controlling or reading data from devices via I2C
Isolated GPIO
for controlling or detecting devices via GPIO
Isolated RS485
Isolated RS232
DC power supply
7 ~ 36V DC input
RS485 terminal resistor and GPIO logic level selection
RS485: connect/disconnect the 120R resistor
GPIO: GPIO logic level selection

RTC battery holder
supports CR1220 button cell
Touch screen header
connected to the capacitive touch screen
Display connector
connected to the 7inch 800×480 display
M.2 M KEY
supports M.2 M KEY NVME SSD, or other communication modules using PCIe channel
Speaker header
audio output
FAN header
for connecting cooling fan, allows speed adjustment and measurement
RTC interruption configuration
GL-EN: CM4 powerdown on RTC interruption
PI-RUN: CM4 will reboot on RTC interruption
D16: D16 pin is triggered on RTC interruption (default)
System function configuration
BT_DIS: Bluetooth disabled, for CM4 with antenna variant ONLY
WiFi_DIS: WiFi disabled, for CM4 with antenna variant ONLY
WP_DIS: boot mode switch, ONLY be used when NOT booted from eMMC or SD card
FAN power supply selection
select 5V (default) or 12V power to drive the fan
IO-VREF selection
set the CM4 IO logic level as 3.3V (default) or 1.8V
RS485 switch
GPIO13/12: using ttyAMA1 device (default)
GPIO15/14: using ttyS0 device
RTC/FAN I2C bus selection
SDA0/SCL0: I2C-10 is shared with CSI/DSI
GPIO3/2: I2C-1 is shared with 40PIN GPIO (default)

WIKI: CM4-DISP-BASE-7A-BOX

Inches	• 7
Κατάσταση	• New

7″ Touch Screen All-In-One Kit Designed for Raspberry Pi CM4, 5MP Camera, Aluminum Case